jivanqui

  • Gesamtaktivitäten 15
  • Letzte Aktivität
  • Mitglied seit
  • Folge ich 0 Benutzer
  • Gefolgt von 0 Benutzer
  • Stimmen 0
  • Abonnements 1

Aktivitätsübersicht

Neueste Aktivität von jivanqui

  • jivanqui hat einen Kommentar hinterlassen

    1. Community
    2. Anybus - Gateways
    3. AB7000C - configuration

    Morning Deryck This configuration works well now. No more problem in hardware plc siemens. The LEDs on the communicators are as follows: 1 - GREEN, 2 - OFF, 3 - OFF, 4 - OFF, 5 - RED, 6 - GREEN fl...

  • jivanqui hat einen Kommentar hinterlassen

    1. Community
    2. Anybus - Gateways
    3. AB7000C - configuration

    Hi Deryck I did the same procedure to another communicator, for humity equipement, restored to the default mailbox configuration, and works well too. Now I can install both anybus communicator in m...

  • jivanqui hat einen Kommentar hinterlassen

    1. Community
    2. Anybus - Gateways
    3. AB7000C - configuration

    Hi Deryck Sorry, yesterday we have a maintenence in stop line, because this I can´t work in the problem anybus. The node id I adjust for 11 (eleven), but I change many times. I already change for o...

  • jivanqui hat einen Kommentar hinterlassen

    1. Community
    2. Anybus - Gateways
    3. AB7000C - configuration

    Deryck How I can do the factory resset?

  • jivanqui hat einen Kommentar hinterlassen

    1. Community
    2. Anybus - Gateways
    3. AB7000C - configuration

    Hi Deryck The LEDs on the communicators are as follows: 1 - OFF, 2 - RED, 3 - OFF, 4 - OFF, 5 - RED, 6 - GREEN flashing

  • jivanqui hat einen Kommentar hinterlassen

    1. Community
    2. Anybus - Gateways
    3. AB7000C - configuration

    Morning Deryck, I did a new test: I put a remote intead gateway, make a new configuration for a new hardware, and you can see the result in pictures bellow: image825Ã709 119 KB image708Ã618 936 ...

  • jivanqui hat einen Kommentar hinterlassen

    1. Community
    2. Anybus - Gateways
    3. AB7000C - configuration

    Sorry, I didn´t undertand. I already download the hardware of plc. But is possible for me do this again anytime is necessary.

  • jivanqui hat einen Kommentar hinterlassen

    1. Community
    2. Anybus - Gateways
    3. AB7000C - configuration

    hi Deryck "Is there communication on the bus?" - I don´t think so, because only side profibus e pc are connect, the RS232 are disconnected. I´m working in laboratory far from the equipment. "Is the...

  • jivanqui hat einen Kommentar hinterlassen

    1. Community
    2. Anybus - Gateways
    3. AB7000C - configuration

    Ok Deryck I did the configuration for Data location, works well. image1023Ã638 88.1 KB I configurated the new words in plc program, but the problem coninuous image1137Ã647 173 KB Another sugges...

  • jivanqui hat einen Kommentar hinterlassen

    1. Community
    2. Anybus - Gateways
    3. AB7000C - configuration

    Ok Deryck Thanks for your help. I tried to change in plc hardware your suggestion, but not work. I check in subnetwork monitor like you show, and I can see that I´ve a colision at In Area, like in ...